Key Features64-bit MIPS-based processor operating at 700 MHz45-Gbps switch fabric and 1.2-Gbps cell-bus (when used with chassis other than the Cisco MGX 8950)Cisco PXM-45/C used only as processor in Cisco MGX 8950; Cisco MGX-XM-60 provides switch-fabric function in that chassisHot swappable1:1 hot-standby redundancyUser-selectable primary and secondary clock sources with graceful switchoverInternal Stratum-3, external Building Integrated Timing Supply (BITS), or in-band clock sourcesIn-band or out-of-band management using EIA/TIA-232 or 10BASE-T control portsSupport for narrowband and broadband service modules scaling from DS-0 to OC-48c/STM-16 or DS-3/E3 to OC-192/STM-64 (depending on the chassis used)Chassis compatibilityCisco MGX 8830/B, MGX 8850, MGX 8850/B, MGX 8880, and MGX 8950Software compatibilityMinimum Cisco MGX software release supporting Cisco PXM-45/C:Cisco MGX 8850 Software Release 4.0.15Cisco MGX 8950 Software Release 4.0.15 Cisco MGX Software Release 5.0.20 (for Cisco MGX 8880 and MGX 8850/B)Cisco MGX Software Release 5.2.00 (for Cisco MGX 8830/B)Network Management Managed by Cisco WAN Manager Software suite Based on Simple Network Management Protocol (SNMP)PowerInput power required: -48 VDCPower consumption: 128 WPhysical DimensionsH x D: 15.75 x 16.5 in. (40.00 x 41.91 cm)Weight6.5 lbs

Key FeaturesThe main features of the Cisco 8-Port OC-12/STM-4 Channelized/Unchannelized ATM Switch Service Module are listed here.Full nonblocking, full-duplex line-rate throughput on all 8 ports when used on the Cisco MGX 8950 chassisUp to 4 ports with nonblocking, full-duplex line-rate throughput when used on the Cisco MGX 8800 chassisIndividual port channelization down to DS-3 and OC-3c/STM-1Per-virtual-path and per-virtual-circuit traffic shaping and available bit rate (ABR) with virtual source and virtual destinationAPS (1:1 and 1+1) port redundancy, plus APS 1+1 card redundancyUp to 4 million cell buffersUp to 16 classes of service (CoS) that can be used to support IP or ATM servicesSupport for standards-based Private Network-to-Network Interface (PNNI), switched virtual circuit (SVC) and switched virtual path (SVP), soft permanent virtual connection (SPVC) and soft permanent virtual path (SPVP), and Multiprotocol Label Switching (MPLS) servicesChassis CompatibilityCisco MGX 8830/B, MGX 8850, MGX 8850/B, MGX 8880, and MGX 8950Software CompatibilityCisco MGX 8800/8900 Software Release 5.2.00 and above for Cisco MGX 8830/B, MGX 8850, MGX 8850/B, and MGX 8950Cisco MGX 8800/8900 Software Release 5.3.00 and above for Cisco MGX 8880ProtocolsATM and SONET/SDHPort Density8 ports (4 ports at full line rate on the Cisco MGX 8800 chassis)Network ManagementManaged by Cisco WAN Manager software suiteBased on Simple Network Management Protocol (SNMP)PowerInput power required: -48 VDC Power consumption: 134WPhysical DimensionsH x D: 15.83 x 15.65 in. (40.20 x 39.75 cm)Weight6.5 lb (2.95 kg)

Key FeaturesThe main features of the Cisco 8-Port OC-12/STM-4 Channelized/Unchannelized ATM Switch Service Module are listed here.Full nonblocking, full-duplex line-rate throughput on all 8 ports when used on the Cisco MGX 8950 chassisUp to 4 ports with nonblocking, full-duplex line-rate throughput when used on the Cisco MGX 8800 chassisIndividual port channelization down to DS-3 and OC-3c/STM-1Per-virtual-path and per-virtual-circuit traffic shaping and available bit rate (ABR) with virtual source and virtual destinationAPS (1:1 and 1+1) port redundancy, plus APS 1+1 card redundancyUp to 4 million cell buffersUp to 16 classes of service (CoS) that can be used to support IP or ATM servicesSupport for standards-based Private Network-to-Network Interface (PNNI), switched virtual circuit (SVC) and switched virtual path (SVP), soft permanent virtual connection (SPVC) and soft permanent virtual path (SPVP), and Multiprotocol Label Switching (MPLS) servicesChassis CompatibilityCisco MGX 8830/B, MGX 8850, MGX 8850/B, MGX 8880, and MGX 8950Software CompatibilityCisco MGX 8800/8900 Software Release 5.2.00 and above for Cisco MGX 8830/B, MGX 8850, MGX 8850/B, and MGX 8950Cisco MGX 8800/8900 Software Release 5.3.00 and above for Cisco MGX 8880ProtocolsATM and SONET/SDHPort Density8 ports (4 ports at full line rate on the Cisco MGX 8800 chassis)Network ManagementManaged by Cisco WAN Manager software suiteBased on Simple Network Management Protocol (SNMP)PowerInput power required: -48 VDC Power consumption: 134WPhysical DimensionsH x D: 15.83 x 15.65 in. (40.20 x 39.75 cm)Weight6.5 lb (2.95 kg)

Key feattures :The Cisco MGX-XM60 Switching Module has the following primary features:Single-height card60-Gbps nonblocking crosspoint switch fabricDynamic sharing of capacity across multiple Cisco XM-60s, allowing for N + 1 redundancyFour installed in each Cisco MGX 8950 for 240-Gbps total capacity, 180-Gbps redundant capacityHot card insertion/removalComplete separation from control processor, allowing data forwarding in the event of control card failureChassis compatibilityMGX 8950Software compatibilityMGX S/W Releases supporting MGX-XM60:MGX Rls 4.0.15 and aboveNetwork managementManaged by Cisco WAN Manager Software suiteBased on Simple Network Management Protocol (SNMP)PowerInput power required: -48 VDCPower consumption: 61 WPhysical dimensionsH x D: 7.25 x 16.5 in. (18.41 x 41.91 cm)Weight3.5 lb

AXSM can be used in the MGX 8850 to provide ATM capability up to OC-48c/STM-16.High scalability in interface speeds with T3/E3 ports, OC-3c/STM-1, OC-12c/STM-4, and OC-48c/ STM-16 AXSM modules. Each port on the AXSM can be configured for either trunk or access applications.Industry leading module port densities of 16 T3/E3 ports, 16 OC-3c/STM-1 ports, 4 OC-12c/STM-4 ports, and 1 OC-48c/ STM-16 port that can scale up to 12 OC-48c/STM-16 modules in each MGX 8850 Multiservice Switch. Each OC-48c/STM-16 delivers fully nonblocking, full duplex throughput, in which a connection can occupy the entire line rate.Support for all ATM service classes, with up to 16 classes of service (CoS). Supports carrier-class implementation of standards-based PNNI, SVC/SVP, SPVC/SPVP, and MPLS services. Large cell buffers (one million cells), which help to maximize "goodput" performance during congestion, reducing the number of retransmits; the buffers are allocated dynamically, depending on connection resource needs, thereby optimizing use of system resources.High reliability with hot-standby 1:1 AXSM card redundancy, 1:1 and 1+1 line redundancy using APS. Ports and trunks supported on same AXSM moduleUser-Network Interface (UNI) Specifications 3.0, 3.1, 4.0Network Management Management using Cisco WAN Manager software suiteBased on Simple Network Management Protocol (SNMP)Physical SpecificationsDimensions: (H x D) 15.83 x 15.65 in.Electrical SpecificationsInput power required: -48 VDCPower consumption: 95W

Key Features: The main features of the Cisco MGX 8800/8900 16-Port OC-3c/STM-1 ATM Switch Service Module are listed here.Full nonblocking, full-duplex line-rate throughput on all 16 portsHigh reliability with hot-standby 1+1 16-port ATM switch service module card redundancyPer-virtual-path and per-virtual-circuit traffic shaping and available bit rate (ABR) with virtual source and virtual destinationY-cable and APS (1:1 and 1+1) port redundancy, plus APS 1+1 card redundancyUp to 4 million cell buffersUp to 16 classes of service (CoS) that can be used to support IP or ATM servicesSupport for standards-based Private Network-to-Network Interface (PNNI), switched virtual circuit (SVC) and switched virtual path (SVP), soft permanent virtual connection (SPVC) and soft permanent virtual path (SPVP), and Multiprotocol Label Switching (MPLS) servicesChassis Compatibility: Cisco MGX 8830/B, MGX 8850, MGX 8850/B, and MGX 8950Software Compatibility: Cisco MGX 8800/8900 SW Release 5.0.20 and aboveProtocols : ATM and SONET/SDHPort Density : 16 portsNetwork Management Managed by Cisco WAN Manager software suite Based on Simple Network Management Protocol (SNMP)PowerInput power required: -48 VDCPower consumption: 114WPhysical DimensionsH x D: 15.83 x 15.65 in. (40.20 x 39.75 cm)Weight6.5 lb (2.95 kg)

Aironet 1542ISemi omnidirectional antenna802.11ac Wave 2 supportMU MIMO 2x2, 2 spatial streamsFlexible deployment with Mobility Expressas traditional APs, and in mesh networksAironet 1542DDirectional antenna802.11ac Wave 2 supportMU-MIMO 2x2, 2 spatial streamsFlexible deployment with Mobility Expressas traditional APs, and in mesh networks802.11ac Wave 1 and 2 capabilities1542I/D: 2 x 2 MIMO with two spatial streamsMultiuser and single user MIMOMaximal Ratio Combining (MRC)802.11ac beamforming (transmit beamforming)20-, 40-, and 80-MHz channelsPHY data rates up to 867 Mbps (80 MHz in 5 GHz)Packet aggregation: A-MPDU (Tx/Rx) and A-MSDU (Tx/Rx)  802.11 Dynamic Frequency Selection (DFS)Cyclic Shift Diversity (CSD) support802.11n (and related) capabilities1542I/D: 2 x 2 MIMO with two spatial streamsMRC20- and 40-MHz channels (40 MHz in 5 GHz)PHY data rates up to 300 MbpsPacket aggregation: A-MPDU (Tx/Rx) and A-MSDU (Tx/Rx)802.11 DFSCSD supportData rates supported: 802.11a: 6, 9, 12, 18, 24, 36, 48, and 54 Mbps802.11b/g: 1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, and 54 Mbps802.11n data rates on 2.4 and 5 GHzMaximum conducted transmit power1542I2.4 GHz: 27 dBm with 2 antennas5 GHz: 25 dBm with 2 antennas1542D2.4 GHz: 27 dBm with 2 antennas5 GHz: 25 dBm with 2 antennasInterfacesWAN port 10/100/1000BASE-T Ethernet autosensing (RJ-45) PoEManagement console port (RJ-45)Multicolor LED/Reset buttonWireless Access802.11i, Wi-Fi Protected Access 2 (WPA2), and WPA802.1X authentication, including Extensible Authentication Protocol (EAP) and Protected EAP (EAP -PEAP), EAP Transport Layer Security (EAP-TLS), EAP-Tunneled TLS(EAP-TTLS), EAP-Subscriber Identity Module (EAP-SIM), and Cisco LEAPVPN pass-throughIP Security (IPsec)Layer 2 Tunneling Protocol (L2TP)MAC address filteringUplink options: Ethernet and wireless meshDimensions(L x W x H):1542I/D: 7.9 x 5.9 x 2.4 in.(20 x 15 x 6.1 cm)Weight1542I/D: 2.75 lb (1.25 kg)Warranty: 1 year limited hardware warranty

Aironet 1562I802.11ac Wave 2 support3x3 MU-MIMO, 3 spatial streamsInternal antennaAironet 1562E802.11ac Wave 2 support2x2 MU-MIMO, 2 spatial streamsFlexible antenna portsExternal antennaAironet 1562D802.11ac Wave 2 support2x2 MU-MIMO, 2 spatial streamsDirectional antenna802.11ac Wave 1 and 2 capabilities1562I: 3 x 3 MIMO with three spatial streams1562E/D 2 x 2 MIMO with two spatial streamsMulti and single user MIMOMaximal Ratio Combining (MRC)802.11ac beamforming (transmit beamforming)20-, 40-, and 80 MHz channelsPHY data rates up to 1.3 Gbps (80 MHz in 5 GHz)Packet aggregation: A MPDU (Tx/Rx) and A MSDU (Tx/Rx)802.11 Dynamic Frequency Selection (DFS)Cyclic Shift Diversity (CSD) support802.11n (and related) capabilities1562I: 3 x 3 MIMO with three spatial streams1562E/D: 2 x 2 MIMO with two spatial streamsMRC20- and 40 MHz channelsPHY data rates up to 450 MbpsPacket aggregation: A-MPDU (Tx/Rx) and A-MSDU (Tx/Rx)802.11 DFSCSD supportData rates supported802.11a: 6, 9, 12, 18, 24, 36, 48, and 54 Mbps802.11b/g: 1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, and 54 MbpsInterfacesWAN port 10/100/1000BASE-T Ethernet, autosensing (RJ-45), PoESFP port (fiber or electrical)Management console port (RJ-45)Multicolor LEDDC power inputReset buttonUplink optionsEthernet, SFP, and wireless mesh (future availability)Dimensions(L x W x D)1562I: 9.0 x 6.8 x 3.9 in (22.9 x 17.1 x 9.8 cm)1562D: 9.0 x 6.8 x 4.3 in (22.9 x 17.1 x 10.9 cm)1562E:: 9.0 x 6.8 x 3.9 in (22.9 x 17.1 x 9.8 cm)Weight1562I: 5.6 lb (2.5 kg)1562D: 5.7 lb (2.6 kg)1562E: 5.6 lb (2.5 kg)Warranty: 1 year limited hardware warranty

802.11ac support4x4 MIMO, 3 spatial streamsFlexible antenna port802.11n Version 2.0 capabilities4x4 MIMO with three spatial streams (3SS)Maximal Ratio Combining (MRC)802.11n and 802.11a/g Beamforming20- and 40-MHz channelsPHY data rates up to 450 Mbps (40 MHz with 5 GHz)Packet aggregation: A-MPDU (Tx/Rx), A-MSDU (Tx/Rx)802.11 Dynamic Frequency Selection (DFS)Cyclic Shift Diversity (CSD) support802.11ac Wave 1 capabilities4x4 MIMO with three spatial streams (3SS)Maximum Ratio Combining (MRC)802.11ac Beamforming20-, 40-, and 80-MHz channelsPHY data rates up to 1.3 Gbps (80 MHz with 5 GHz)Packet aggregation: A-MPDU (Tx/Rx), A-MSDU (Tx/Rx)802.11 Dynamic Frequency Selection (DFS)Cyclic Shift Diversity (CSD) supportData Rates Supported: 2.4 GHz - 802.11b/g: 1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, and 54 MbpsInterfaceWAN port 10/100/1000BASE T Ethernet, autosensing (RJ-45)LAN port 10/100/1000BASE T Ethernet, autosensing (RJ-45)Fiber SFPCable modem: NA-DOCSIS3.0/Euro-DOCSIS3.0/Japan-DOCSIS3.0 (8x4, 16x8, or 24x8)Management console port (RJ-45)Four multicolor LEDsReset buttonUplink options1572EAC Ethernet, Fiber SFP, Wireless Mesh1572IC Ethernet, Fiber SFP, Wireless Mesh, Cable Modem1572EC Ethernet, Fiber SFP, Wireless Mesh, Cable ModemDimensions (L x W x D): 1572EAC / 1572EC 11.8 x 7.9 x 6.3 in. (30.0 x 20.1 x 16.0 cm)1572IC 11.8 x 7.9 x 7.9 in. (30.0 x 20.1 x 20.1 cm)Weight1572EAC/1572EC 13.5 lbs (6.1 kg)1572IC 11.5 lbs (5.2 kg)Pole mounting Kit 1 (PMK1):2.2 lbs (1.0 kg)Pole mounting Kit 2 (PMK2):4.4 lbs (2.0 kg)Pole mounting Kit 3 (PMK3):6.1 lbs (2.8 kg)Cable strand mounting bracket 1 (SMK1): 0.3 lbs (0.2 kg)Cable strand mounting bracket 2 (SMK2): 0.7 lbs (0.3 kg)Cable strand mounting bracket 2 (SMK3): 1.2 lbs (0.5 kg)Warranty: 1 year limited Hardware warranty

Three radios: 2.4GHz (4x4), 5GHz (4x4), and BLE, Supports OFDMA and MU-MIMO, Internal and external antennaSoftware: Cisco Unified Wireless Network Software Release 8.9 or laterCisco IOS XE Software Release 16.11 or laterSupported wireless LAN controllers: Cisco Catalyst 9800 Series Wireless ControllersCisco 3500, 5520, and 8540 Series Wireless Controllers and Cisco Virtual Wireless Controller802.11n version 2.0 (and related) capabilities4x4 MIMO with four spatial streamsMaximal Ratio Combining (MRC)802.11n and 802.11a/g beamforming20- and 40-MHz channelsPHY data rates up to 890 Mbps (40 MHz with 5 GHz and 20 MHz with 2.4 GHz)Packet aggregation: A-MPDU (transmit and receive), A-MSDU (transmit and receive)802.11 Dynamic Frequency Selection (DFS)Cyclic Shift Diversity (CSD) support802.11ac4x4 downlink MU-MIMO with four spatial streamsMRC802.11ac beamforming20-, 40-, 80-, and 160-MHz channelsPHY data rates up to 3.47 Gbps (160 MHz with 5 GHz)Packet aggregation: A-MPDU (transmit and receive), A-MSDU (transmit and receive)802.11 DFSCSD support802.11ax4x4 downlink MU-MIMO with four spatial streamsUplink/downlink OFDMATWTBSS coloringMRC802.11ax beamforming20-, 40-, 80-, and 160-MHz channelsPHY data rates up to 5.38 Gbps (160 MHz with 5 GHz and 20 MHz with 2.4 GHz)Packet aggregation: A-MPDU (transmit and receive), A-MSDU (transmit and receive)802.11 DFSCSD supportIntegrated antenna: 2.4 GHz, peak gain 3 dBi, internal antenna, omnidirectional in azimuth5 GHz, peak gain 4 dBi, internal antenna, omnidirectional in azimuthExternal antenna (sold separately)Cisco Catalyst 9115AXE Access Points are certified for use with antenna gains up to 6 dBi (2.4 GHz and 5 GHz)Cisco offers the industry's broadest selection of antennas, delivering optimal coverage for a variety of deployment scenariosInterfaces: 1x 100, 1000, 2500 Multigigabit Ethernet (RJ-45) – IEEE 802.3bzManagement console port (RJ-45), USB 2.0 (enabled via future software)Indicators: Status LED indicates boot loader status, association status, operating status, boot loader warnings, and boot loader errorsDimensions (W x L x H)Access point (without mounting brackets): C9115I: 8.0 x 8.0 x 1.5 in. (20.3 x 20.3 x 3.8 cm), C9115E: 8.0 x 8.0 x 1.7 in. (20.3 x 20.3 x 4.3 cm)Weight: Cisco Catalyst 9115AXI, 1.98 lb (0.9 kg)Cisco Catalyst 9115AXE, 2.43 lb (1.1 kg)System memory: 2048 MB DRAM, 1024 MB flashWarranty: Limited lifetime hardware warranty

Four radios: 2.4 GHz (4x4), 5 GHz (4x4), Cisco RF ASIC and BLE/IoTCisco Flexible Radio Assignment and Cisco CleanAir TechnologyInternal and external antennaSoftwareCisco Unified Wireless Network Software Release 8.9.x or laterCisco IOS XE Software Release 16.11 with AP Device Pack, or laterSupported wireless LAN controllersCisco Catalyst 9800 Series Wireless ControllersCisco 3500, 5520, and 8540 Series Wireless Controllers and Cisco Virtual Wireless Controller802.11n version 2.0 (and related) capabilities4x4 MIMO with four spatial streamsMaximal Ratio Combining (MRC)802.11n and 802.11a/g beamforming20- and 40-MHz channelsPHY data rates up to 890 Mbps (40 MHz with 5 GHz and 20 MHz with 2.4 GHz)Packet aggregation: A-MPDU (transmit and receive), A-MSDU (transmit and receive)802.11 Dynamic Frequency Selection (DFS)Cyclic Shift Diversity (CSD) support802.11ac4x4 downlink MU-MIMO with four spatial streamsMRC802.11ac beamforming20-, 40-, 80-, and 160-MHz channelsPHY data rates up to 3.47 Gbps (160 MHz with 5 GHz)Packet aggregation: A-MPDU (transmit and receive), A-MSDU (transmit and receive)802.11 DFSCSD support802.11ax4x4 downlink MU-MIMO with four spatial streamsUplink/downlink OFDMATWTBSS coloringMRC802.11ax beamforming20-, 40-, 80-, and 160-MHz channelsPHY data rates up to 5.38 Gbps (160 MHz with 5 GHz and 20 MHz with 2.4 GHz)Packet aggregation: A-MPDU (transmit and receive), A-MSDU (transmit and receive)802.11 DFSCSD supportInterfaces: 1x 100, 1000, 2500 Multigigabit Ethernet (RJ-45)IEEE 802.3bzManagement console port (RJ-45), USB 2.0 3.75W (enabled via future software)Indicators: Status LED indicates boot loader status, association status, operating status, boot loader warnings, and boot loader errorsDimensions (W x L x H)Access point (without mounting brackets): C9120I: 8.5 x 8.5 x 1.7 (21.6 x 21.6 x 4.3 cm), C9120E and C9120P: 8.5 x 8.05x 2.0 (21.6 x 21.6 x 5.1 cm)Weight: Cisco Catalyst 9120I, 2.87 lbs (1.3 kg)Cisco Catalyst 9120E/P, 3 lbs (1.36 kg)System memory: 2048 MB DRAM, 1024 MB flashWarranty: Limited lifetime hardware warranty

Three radios: 2.4GHz (4x4), 5GHz (8x8), and BLE, Supports OFDMA and MU-MIMO, Internal antennaSoftware: Cisco Unified Wireless Network Software Release 8.9 or laterCisco IOS XE Software Release 16.11 or laterSupported wireless LAN controllers: Cisco Catalyst 9800 Series Wireless ControllersCisco 3500, 5520, and 8540 Series Wireless Controllers, and Cisco Virtual Wireless Controller802.11n version 2.0 (and related) capabilities8x8 MIMO with four spatial streams for 5 GHz band4x4 MIMO with four spatial streams for 2.4 GHz bandMaximal Ratio Combining (MRC)20- and 40-MHz channelsPHY data rates up to 600 Mbps (40 MHz with 5 GHz)Packet aggregation: A-MPDU (transmit and receive), A-MSDU (transmit and receive)Cyclic Shift Diversity (CSD) support802.11ac8x8 downlink MU-MIMO with eight spatial streamsMRC802.11ac beamforming20-, 40-, 80, and 160 MHz channelsPHY data rates up to 3.5 Gbps at 5 GHzPacket aggregation: A-MPDU (transmit and receive), A-MSDU (transmit and receive)CSD support160 MHz support only on 4 spatial stream802.11ax8x8 MIMO with eight spatial streams for 5-GHz band4x4 MIMO with four spatial streams for 2.4-GHz bandDownlink OFDMATWTMRC802.11ax beamforming20-, 40-, 80, and 160 MHz channelsPHY data rates up to 5 Gbps at 5 GHzPacket aggregation: A-MPDU (transmit and receive), A-MSDU (transmit and receive)CSD supportIntegrated antenna: 2.4 GHz, peak gain 4 dBi, internal antenna, omnidirectional in azimuth5 GHz, peak gain 6 dBi, internal antenna, omnidirectional in azimuthInterfaces: 1x 100, 1000, 2500, 5000 Multigigabit Ethernet (RJ-45)IEEE 802.3bzManagement console port (RJ-45)USB 2.0 with up to 4.5W (enabled via future software)Indicators: Status LED indicates boot loader status, association status, operating status, boot loader warnings, and boot loader errorsDimensions (W x L x H)Access point (without mounting bracket and mounting features): 8.70 x 8.70 x 1.94 in. (22 x 22 x 4.93 cm)Access point (without mounting bracket): 8.70 x 8.70 x 2.19 in. (22 x 22 x 5.56 cm)Weight: 3.02 lb (1.4 kg)System memory: 2048 MB DRAM, 1024 MB flashWarranty: Limited lifetime hardware warranty

Four radios: 2.4 GHz (4x4), 5 GHz (8x8 and 4x4), Cisco RF ASIC, and BLE/IoTCisco Flexible Radio Assignment and Cisco CleanAir TechnologyInternal and external antennaWiFi 6 certifiedSoftware: Catalyst 9130 AXI: Cisco Unified Wireless Network Software Release 8.10.x or laterCisco IOS XE Software Release 16.12.1 with AP Device Pack, or laterCatalyst 9130AXE: Cisco Unified Wireless Network Software Release 8.10MR1 or laterCisco IOS XE Software Release 17.1.1 s or laterSupported wireless LAN controllers: Cisco Catalyst 9800 Series Wireless ControllersCisco 3504, 5520, and 8540 Wireless Controllers and Cisco Virtual Wireless Controller802.11n version 2.0 (and related) capabilities4x4 MIMO with four spatial streamsMaximal Ratio Combining (MRC)802.11n and 802.11a/g20- and 40 MHz channelsPHY data rates up to 1.5 Gbps (40 MHz with 5 GHz and 20 MHz with 2.4 GHz)Packet aggregation: Aggregate MAC Protocol Data Unit (A-MPDU) (transmit and receive), Aggregate MAC Service Data Unit (A-MSDU) (transmit and receive)802.11 Dynamic Frequency Selection (DFS)Cyclic Shift Diversity (CSD) support802.11ac8x8 downlink MU-MIMO with eight spatial streamsMRC802.11ac beamforming20-, 40-, 80-, and 160-MHz channelsPHY data rates up to 6.9 Gbps (160 MHz with 5 GHz)Packet aggregation: A-MPDU (transmit and receive), A-MSDU (transmit and receive)802.11 DFSCSD supportWPA3 support802.11ax8x8 uplink/downlink MU-MIMO with eight spatial streamsUplink/downlink OFDMATWTBSS coloringMRC802.11ax beamforming20-, 40-, 80-, and 160-MHz channelsPHY data rates up to 10 Gbps (160 MHz with 5 GHz and 20 MHz with 2.4 GHz)Packet aggregation: A-MPDU (transmit and receive), A-MSDU (transmit and receive)802.11 DFSCSD supportWPA3 supportSystem memory: 2048 MB DRAM, 1024 MB flashInterfaces1x 100, 1000, 2500, 5000 Multigigabit Ethernet (RJ-45) – IEEE 802.3azManagement console port (RJ-45)USB 2.0 at 4.5W (enabled via future software)Dimensions (W x L x H)Access point (without mounting brackets):C9130AXI: 8.9 x 8.9 x 1.88 in. (22.6 x 22.6 x 4.8 cm)C9130AXE: 9.17 x 9.17 x 1.58 in. (23.3 x 23.3 x 4.0 cm)Weight: Cisco Catalyst 9130AXI, 3.2 lb. (1.45 kg)Cisco Catalyst 9130AXE, 3.78 lb. (1.71 kg)Warranty: Limited lifetime hardware warranty

Catalyst 9800 embedded on a Catalyst 9000 switchIdeal for SD-Access-enabled distributed branches and small campusesUp to 200 APs and 4 000 clientsHot patching  time saving and hitless upgradeSimplified device deploymentUnified management of wired and wireless networksNetwork virtualization and segmentationGroup-based policiesContext-based analyticsLicensing Packaging : The Cisco Catalyst 9000 family of switches introduces a new and simplified licensing package in the form of base and add-on licenses.The perpetual licensing package includes the Network Essentials and Network Advantage licensing options that are tied to the hardware. Between them  the base licensing packages cover switching fundamentals  management automation  troubleshooting  and advanced switching features. These Network licenses are perpetual.The subscription licensing package includes the Cisco DNA Essentials and Cisco DNA Advantage options. In addition to on-box capabilities  the features available with this package provide Cisco innovations on the switch  as well as on Cisco DNA Center. The Cisco DNA subscription licenses are mandatory at the time of configuration.License consumption is easily determined by the package itself. While perpetual licenses are always permanent and without an expiration date  subscription licenses have to be purchased for a 3-, 5-, or 7-year term (and hence are also known as term-based licenses). Table 12 shows the combinations of perpetual and subscription licenses that must be purchased.Connectors and cabling1000BASE-T ports: RJ-45 connectors  4-pair Cat 5E UTP cablingMultigigabit-T ports: RJ-45 connectors  4-pair Cat 5E  Cat 6  Cat 6A UTP cabling1000BASE-T SFP-based ports: RJ-45 connectors  4-pair Cat 5E UTP cabling SFP transceivers: LC fiber connectors (single-mode or multimode fiber) SFP+ transceivers: LC fiber connectors (single-mode or multimode fiber) QSFP+ transceivers: MPO and LC fiber connectors (single-mode or multimode fiber) QSFP+ connector SFP+ connector Cisco StackWise stacking ports: copper-based Cisco StackWise cabling Cisco StackPower: Cisco proprietary power stacking cables Ethernet management port: RJ-45 connectors  4-pair Cat 5 UTP cabling Management console port: RJ-45-to-DB9 cable for PC connections

ISR 4221GE/SFP integrated WAN ports1.2 Gbps performance75 Mbps encrypted throughputAggregate Throughput 35 Mbps to 75 MbpsTotal onboard WAN or LAN 10/100/1000 ports 2RJ-45 based ports 2SFP based ports 1NIM (Network Interface Modules): slots 2Onboard ISC slot NoDefault memory double data rate 3 (DDR3) error correction code(ECC) DRAM (Combined control/services/data planes): 4 GBFlash Memory: 8 GBPower supply: options External AC onlyRack height: 1 RUUSB console port: type B mini (up to 115.2 kbps) 0Serial console port: RJ45 (up to 115.2 kbps) 1 (combo CON/AUX port)Serial auxiliary port: RJ45(up to 115.2 kbps)1 (combo CON/AUX port)Power supply options External: AC OnlyRedundant power supply N/AAC input voltage 100 to 240 VAC autorangingAC input frequency 47 to 63 HzAC input current range, AC power supply (maximum) 1.5 to 0.6AAC input surge current 90 A peak and less than 3 Arms per half cycleTypical power (no modules) (watts): 24Maximum power with AC power supply (watts): 90Maximum power with PoE power supply (platform only) (watts) NA (no PoE support)Maximum endpoint PoE power available from PoE power supply (watts) NA (no PoE support)Dimensions (H x W x D): 1.72 x 12.7 x 10 in (43.7 x 322.6 x 254 mm)Weight with AC PS (no modules): 7.1 lb (3.22 kg)ISR 4331GE/SFP integrated WAN ports2 Gbps+ performance500 Mbps encrypted throughputAggregate Throughput 100 Mbps to 300 MbpsTotal onboard WAN or LAN 10/100/1000 ports 3RJ-45 based ports: 2SFP based ports: 2Enhanced service module (SM-X): slot 1NIM (Network Interface Modules): slots 2Onboard ISC slot 1Memory: 4 GB (default) / 16 GB (maximum)Flash Memory: 4 GB (default) / 16 GB (maximum)Power supply options Internal: AC and PoERack height: 1 RUNIM slots 2OIR (all I/O modules): YesOnboard ISC slot 1Default memory double data rate 3 (DDR3) error-correction-code (ECC) DRAM(Combined control/services/data planes) 4 GBMaximum memory DDR3 ECC DRAM (Combined control/services/data planes) 16 GBDefault memory DDR3 ECC DRAM (data plane) NAMaximum memory DDR3 ECC DRAM (data plane) NADefault memory DDR3 ECC DRAM (control/services plane) NAMaximum memory DDR3 ECC DRAM (control/services plane) NADefault flash memory: 4 GBMaximum flash memory: 16 GBExternal USB 2.0 slots (type A) 1USB console port: type B mini (up to 115.2 kbps) 1Serial console port: RJ45 (up to 115.2 kbps) 1Serial auxiliary port: RJ45(up to 115.2 kbps) 1Power-supply options Internal: AC and PoERedundant power supply N/AAC input voltage 100 to 240 VAC autorangingAC input frequency 47 to 63 HzAC input current range, AC power supply (maximum) 3 to 1.3AAC input surge current 60 A peak and less than 5 Arms per half cycleTypical power (no modules) (watts) 42Maximum power with AC power supply (watts) 250Maximum power with PoE power supply (platform only) (watts) 530Maximum endpoint PoE power available from PoE power supply (watts) 250Dimensions (H x W x D): 44.45 x 438.15 x 438.15 mmPackage Weight: 12.96 KgISR 4431PoE GE/SFP, GE/SFP integrated WAN ports4 Gbps + performance900 Mbps encrypted throughputAggregate Throughput 500 Mbps to 1 GbpsTotal onboard WAN or LAN 10/100/1000 ports 4RJ-45 based ports: 4SFP-based ports: 4Enhanced service module (SM-X) slot 0NIM (Network Interface Modules) slots 3Onboard ISC slot 1DDRM (data plane): 2 GB (default) / 2 GB (maximum)DDRM (control/services plane): 4 GB (default) / 16 GB (maximum)Flash Memory: 8 GB (default) / 32 GB (maximum)Power supply options Internal: AC, DC, and PoERack height: 1 RUDoublewide service module slots 0NIM slots 3OIR (all I/O modules): YesOnboard ISC slot 1Default memory double data rate 3 (DDR3) error correction code (ECC) DRAM(Combined control/services/data planes)NAMaximum memory DDR3 ECC DRAM (Combined control/services/data planes) NADefault memory DDR3 ECC DRAM (data plane) 2 GBMaximum memory DDR3 ECC DRAM (data plane) 2 GBDefault memory DDR3 ECC DRAM (control/services plane) 4 GBMaximum memory DDR3 ECC DRAM (control/services plane) 16 GBDefault flash memory: 8 GBMaximum flash memory: 32 GBExternal USB 2.0 slots (type A) 2USB console port: type B mini (up to 115.2 kbps) 1Serial console port: RJ45 (up to 115.2 kbps) 1Serial auxiliary port: RJ45 (up to 115.2 kbps) 1Power-supply options Internal: AC, DC, and PoERedundant power supply Internal: AC, DC, and PoEAC input voltage 100 to 240 VAC autorangingAC input frequency 47 to 63 HzAC input current range, AC power supply (maximum) 3 to 1.3AAC input surge current 60 A peak and less than 5 Arms per half cycleTypical power (no modules) (watts) 65Maximum power with AC power supply (watts) 250 (no PoE)Maximum power with PoE power supply (platform only) (watts) 500 with PoE redundantMaximum endpoint PoE power available from PoE power supply (watts) 250 W with optional redundancyDimensions (H x W x D): 43.9 x 438.15 x 507.2 mmPackage Weight: 20.88 KgISR 446110 GE SFP+, PoE GE/SFP, GE/SFP integrated WAN ports10 Gbps+ performance7 Gbps encrypted throughputAggregate Throughput 1.5GbpsTotal onboard WAN or LAN 10/100/1000 ports 4RJ-45 based ports: 4SFP based ports: 4Enhanced service module slots 3Doublewide service: module slots 2NIM slots 3OIR (all I/O modules): YesOnboard ISC slot 1SFP based ports 4Enhanced service module slots 3Doublewide service module slots 2NIM slots 3OIR (all I/O modules): YesOnboard ISC slot 1Default memory double-data-rate 3 (DDR3) error-correctioncode (ECC) DRAM (Combined control/services/data planes)- Not available Maximum memory DDR3 ECC DRAM (Combined control/services/data planes)- Not available Default memory DDR3 ECC DRAM (data plane) 4 GBMaximum memory DDR3 ECC DRAM (data plane) 4 GBDefault memory DDR3 ECC DRAM (control/services plane) 8 GBMaximum memory DDR3 ECC DRAM (control/services plane) 32 GBDefault flash memory: 8 GBMaximum flash memory: 32 GBExternal USB 2.0 slots (type A) 2USB console port: type B mini (up to 115.2 kbps) 1Serial console port: RJ45 (up to 115.2 kbps) 1Serial auxiliary port: RJ45 (up to 115.2 kbps) 1Power-supply options Internal: AC, DC and PoERedundant power supply Internal: AC, DC and PoEDimensions (H x W x D): 3.5 x 17.25 x 18.5 in(88.9 x 438.15 x 469.9 mm)Rack height 2 Rack Units (2RU)

Pay as you grow performance (44 - 100 Gbps)Optional field replacement and Crypto module capability of up to 25 Gbps bandwidth with performance licensesSupport for built in front panel 4xGE and 4x10GE; upgradeable to 8xGE amd 8x10GE with a licenseExtendable I/O with 1 Ethernet port adapter, and 1 single wide network interface module (NIM) or 1 double wide NIMTwo AC or DC power suppliesOne field replaceable fan tray for front to back airflowThe ASR 1002 HX is ideal for large enterprise branch offices, and as a high-performing edge solution for a private WAN It supportsWAN aggregation and highly secure WANInternet edgeData center interconnectCisco Intelligent WAN (IWAN)Scalability: 44 Gbps – 100 GbpsEmbedded service processor slots: IntegratedRoute processor slots: IntegratedRedundancy: SoftwareRedundant power supply: DualHitless software upgrade: Not available Programming interface: XML and CLI scriptManagement tool: Cisco Prime Network Analysis Module

ISR 1100 4G/6G/LTEViptela OSCisco SD WAN4-6 GE WAN/LAN portsISR 1101IOS XE/IOS XE SD-WANCisco SD-WAN4 GE WAN/LAN portsPluggable LTEISR 1109IOS XE/IOS XE SD WANCisco SD WAN2-4 GE WAN/LAN portsDual pluggable LTEISR 111xIOS XE/IOS XE SD WANCisco SD WAN4-8 GE WAN/LAN portsPoEISR 1111XIOS XE/IOS XE SD-WANCisco SD-WAN security8 GE WAN/LAN portsPoEISR 1120IOS XE/IOS XE SD WANCisco SD-WAN security8 GE WAN/LAN portsPluggable LTE, WiFi, DSL optionsISR 1160IOS XE/IOS XE SD-WANCisco SD-WAN security8 GE WAN/LAN portsPluggable LTE option

Ports : 48 x 10/25-Gbps and 6 x 40/100-Gbps QSFP28 portsDownlink supported speeds : 1/10/25-Gbps speedsCPU: 4 coresSystem memory: 24 GBSSD drive : 64 GBSystem buffer: 40 MBManagement ports 2 ports: 1 RJ-45 and 1 SFPUSB ports : 1RS-232 serial ports :  1Power supplies (up to 2) : 650W AC, 930W DC, or 1200W HVAC/HVDCTypical power (AC/DC) :  210WMaximum power (AC/DC) :  470WPhysical dimensions c(H x W x D)1.72 x 17.3 x 22.5 in.(4.4 x 43.9 x 57.1 cm)Weight (without power supplies or fans) 17.2 lb (7.8 kg)N9K-C93180YC-EX is one of the Cisco Nexus 9300-EX switches. Cisco Nexus 9300-EX platforms are the next generation of fixed Cisco Nexus9000 Series Switches. The new platforms support cost-effective cloud-scale deployments, an increased number of endpoints, and cloud serviceswith wire-rate security and telemetry. The platforms are built on modern system architecture designed to provide high performance and meetthe evolving needs of highly scalable data centers and growing enterprises.

Device Type : Switch - 24 ports - L3Enclosure Type : Rack-mountable 1USubtype : 50 Gigabit EthernetPorts : 24 x 40/50 Gigabit QSFP+ + 6 x 40/100 Gigabit QSFP+Performance : Bandwidth: 3.6 Tbps ¦ Active SPAN sessions: 4Capacity : Multiple Spanning Tree Protocol instances: 64 ¦ HSRP groups: 490 ¦ Per VLAN Rapid Spanning Tree instances: 4000 ¦ Maximum number of links in a port channel: 32 ¦ Maximum number of port channels: 512 ¦ ECMP paths: 64 ¦ Virtual Routing and Forwarding (VRF) instances: 1000 ¦ VLANs supported: 4096 ¦ ACL entries (egress): 2000 ¦ ACL entries (ingress): 4000 ¦ IGMP snooping groups: 8000 ¦ Multicast routes: 8000MAC Address Table Size : 512K entriesRouting Protocol :OSPF, RIP, RIP-2, BGP, EIGRP, HSRP, PIM-SM, MSDP, ECMP, MPLSFeatures : Layer 3 switching, High Availability, hot swappable 4 fans, Virtual PortChannel (vPC) technology, In-Service Software Upgrade (ISSU), NPV Gateway mode, Virtual Extensible LAN (VXLAN), Source-Specific Multicast (SSM), Ethernet Virtual Private Network (EVPN), 40MB system bufferRAM : 24 GBBuilt-in Devices : 64 GB SSDThe Cisco Nexus 93180LC-EX Switch is the industry's first 50-Gbps capable 1RU switch that supports 3.6 Tbps of bandwidth and over 2.6 bpps across 24 fixed 40/50-Gbps QSFP+ ports. Ports numbered 25, 27, 29, 30, 31, and 32 are the 6 uplinks ports, which can be configured as 40- and 100-Gbps ports, offering flexible migration options. This switch is capable of supporting flexible port configurations.

Ports :  16 x 400/100/40-Gbps QSFP-DD portsSystem memory :  16 GB NX-OS, 24 GB ACISolid-State Disk (SSD) :  128 GBUSB  1 portRS-232 serial console ports 1Management ports 2 (1 x 10/100/1000BASE-T and 1 x 1-Gbps SFP+)Broadwell-DE CPU 4 coresDimensions (H x W x D) 3.38 x 17.37 x 22.27 in. (8.59 x 44.13 x 56.58 cm)N9K-C9316D-GX is the Cisco Nexus 9316D Spine switch with 16p 400/100G QSFP-DD. Based on Cisco® Cloud Scale technology, the CiscoNexus® 9300-GX switches are the next generation of fixed Cisco Nexus 9000 Series Switches. The platform introduces a fully backwardcompatible 400G optical interface Quad Small Form-Factor Pluggable – Double Density (QSFP-DD) to transparently migrate existing data centerfabrics from 40-Gbps and 100-Gbps speeds to 400 Gbps. The platform provides investment protection for customers, delivering highly flexiblelayer 2 and layer 3 scalability, and performance to meet the changing needs of virtualized data centers and automated cloud environments.

Ports  : 28 x 100/40-Gbps QSFP28 ports and 8 x 400/100-Gbps QSFP-DD portsSystem memory :  16 GB NX-OS, 24 GB ACISolid-State Disk : (SSD) 128 GBUSB : 1 portRS-232 serial console ports  : 1Management ports : 2 (1 x 10/100/1000BASE-T and 1 x 1-Gbps SFP+)Broadwell-DE CPU  : 4 coresDimensions (H x W x D) 1.72 x 17.37 x 25.5 in. (4.37 x 44.13 x 64.8 cm)N9K-C93600CD-GX is the Cisco Nexus 9316D Spine and Leaf switch with 28p 100/40G QSFP28 and 8p 400/100G QSFP-DD. Based on CiscoCloud Scale technology, the Cisco Nexus 9300-GX switches are the next generation of fixed Cisco Nexus 9000 Series Switches. The platformintroduces a fully backward-compatible 400G optical interface Quad Small Form-Factor Pluggable – Double Density (QSFP-DD) to transparentlymigrate existing data center fabrics from 40-Gbps and 100-Gbps speeds to 400 Gbps. The platform provides investment protection forcustomers, delivering highly flexible layer 2 and layer 3 scalability, and performance to meet the changing needs of virtualized data centers andautomated cloud environments.

Features and CapabilitiesThe Cisco Nexus 9504 Switch offers a comprehensive feature set, high resiliency, and a broad range of high performance Gigabit Ethernet line cards. It can meet the most demanding requirements of enterprise, service provider, and cloud data centers.Deployment FlexibilitySupport for the next-generation data center based on Cisco ACINexus Fabric Manager support to automate fabric configuration and managementTraditional data centers in standalone NX-OS modeProgrammabilityOpen API to manage the switch through remote-procedure calls (JavaScript Object Notation or XML) over HTTP or HTTPSAutomated configuration through Linux shell scriptsSupport for customer applications through a Linux container environmentProgrammable APIs for integration with DevOps automation toolsHigh AvailabilityIn-Service Software Upgrade (ISSU) and patching without operation interruption Redundant and hot-swappable supervisors, system controllers, power supplies, and fan traysMix of third-party and Cisco application-specific integrated circuits (ASICs) for improved reliabilityEnergy EfficiencyDesigned without a midplane to optimize front-to-back airflow and reduce power consumptionOptimized design with fewer ASICs, resulting in lower energy useEfficient power supplies that are rated at 80 Plus Platinum Nonblocking performance 15 Tbps10 Gigabit Ethernet nonblocking ports Up to 51225 Gigabit Ethernet Ports Up to 51250 Gigabit Ethernet Ports Up to 25640/100 Gigabit Ethernet nonblocking ports Up to 1441/10GBASE-T nonblocking ports Up to 192Form factor 7-rack-unit chassisLine card slots 4Airflow Front to back

Features and CapabilitiesThe Cisco Nexus 9508 Switch offers a comprehensive feature set, high resiliency, and a broad range of 1/10/40 Gigabit Ethernet line cards to meet the mostdemanding requirements of enterprise, service provider, and cloud data centers.ACI SupportDesigned to support the Cisco next-generation data center based on Cisco ACIProgrammabilityOpen API to manage the switch through remote-procedure calls (JavaScript Object Notation or XML) over HTTP or HTTPSAutomated configuration through Linux shell scriptsSupport for customer applications through a Linux container environmentHigh AvailabilityFull Cisco In-Service Software Upgrade (ISSU) and patching supportRedundant and hot-swappable supervisors, system controllers, power supplies, and fan traysMix of third-party and Cisco application-specific integrated circuits (ASICs) for improved reliabilityEnergy EfficiencyDesign without a midplane to optimize front-to-back airflow and reduce power consumptionOptimized design with fewer ASICs, resulting in lower energy useEfficient power supplies that are rated at 80 Plus PlatinumSpecifications at a Glance30 Tbps of nonblocking performanceUp to 1152 10 Gigabit Ethernet nonblocking portsUp to 288 40 Gigabit Ethernet nonblocking portsUp to 384 1/10GBASE-T nonblocking ports13-rack-unit chassis8 line card slotsFront-to-back airflow

Features and capabilities: The Cisco Nexus 9516 Switch offers a comprehensive feature set, high resiliency, and a broad range of 1/10/40 Gigabit Ethernet line cards. It can meet the most demanding requirements of enterprise, service provider, and cloud data centers.Cisco ACI supportDesigned to support the Cisco next-generation data center based on Cisco ACIProgrammabilityOpen API to manage the switch through remote-procedure calls (JavaScript Object Notation or XML) over HTTP or HTTPSAutomated configuration through Linux shell scriptsSupport for customer applications through a Linux container environmentHigh availabilitySoftware patching for continued operationsRedundant and hot-swappable supervisors, system controllers, power supplies, and fan traysMix of third-party and Cisco application-specific integrated circuits (ASICs) for improved reliabilityEnergy efficiencyDesign without a midplane to optimize front-to-back airflow and reduce power consumptionOptimized design with fewer ASICs, resulting in lower energy useEfficient power supplies that are rated at 80 Plus PlatinumInvestment protection40 Gb  for reuse of existing 10 Gigabit Ethernet multimode cabling plant for 40 Gigabit EthernetSupport for Cisco NX-OS and Cisco ACI modes of operationSupport for Cisco Nexus 2000 Series Fabric ExtendersForm factor : 21 RULine card slots : 16Supervisor slots : 2Fabric module slots : 6ACI support :YesBandwidth per slot (Tbps) : 3.84Bandwidth per system (Tbps) : 60Maximum number of 1/10G BASE-T ports : 768Maximum number of 10 GE ports : 2304Maximum number of 40 GE ports : 576Maximum number of 100GE ports : 576Airflow : Front to backPower supplies (3-kW AC/DC) : Up to 10Fan trays : 3

Key feattures :The Cisco MGX-XM60 Switching Module has the following primary features:Single-height card60-Gbps nonblocking crosspoint switch fabricDynamic sharing of capacity across multiple Cisco XM-60s, allowing for N + 1 redundancyFour installed in each Cisco MGX 8950 for 240-Gbps total capacity, 180-Gbps redundant capacityHot card insertion/removalComplete separation from control processor, allowing data forwarding in the event of control card failureChassis compatibilityMGX 8950Software compatibilityMGX S/W Releases supporting MGX-XM60:MGX Rls 4.0.15 and aboveNetwork managementManaged by Cisco WAN Manager Software suiteBased on Simple Network Management Protocol (SNMP)PowerInput power required: -48 VDCPower consumption: 61 WPhysical dimensionsH x D: 7.25 x 16.5 in. (18.41 x 41.91 cm)Weight3.5 lb

Key FeaturesThe main features of the Cisco 8-Port OC-12/STM-4 Channelized/Unchannelized ATM Switch Service Module are listed here.Full nonblocking, full-duplex line-rate throughput on all 8 ports when used on the Cisco MGX 8950 chassisUp to 4 ports with nonblocking, full-duplex line-rate throughput when used on the Cisco MGX 8800 chassisIndividual port channelization down to DS-3 and OC-3c/STM-1Per-virtual-path and per-virtual-circuit traffic shaping and available bit rate (ABR) with virtual source and virtual destinationAPS (1:1 and 1+1) port redundancy, plus APS 1+1 card redundancyUp to 4 million cell buffersUp to 16 classes of service (CoS) that can be used to support IP or ATM servicesSupport for standards-based Private Network-to-Network Interface (PNNI), switched virtual circuit (SVC) and switched virtual path (SVP), soft permanent virtual connection (SPVC) and soft permanent virtual path (SPVP), and Multiprotocol Label Switching (MPLS) servicesChassis CompatibilityCisco MGX 8830/B, MGX 8850, MGX 8850/B, MGX 8880, and MGX 8950Software CompatibilityCisco MGX 8800/8900 Software Release 5.2.00 and above for Cisco MGX 8830/B, MGX 8850, MGX 8850/B, and MGX 8950Cisco MGX 8800/8900 Software Release 5.3.00 and above for Cisco MGX 8880ProtocolsATM and SONET/SDHPort Density8 ports (4 ports at full line rate on the Cisco MGX 8800 chassis)Network ManagementManaged by Cisco WAN Manager software suiteBased on Simple Network Management Protocol (SNMP)PowerInput power required: -48 VDC Power consumption: 134WPhysical DimensionsH x D: 15.83 x 15.65 in. (40.20 x 39.75 cm)Weight6.5 lb (2.95 kg)

Key Features64-bit MIPS-based processor operating at 700 MHz45-Gbps switch fabric and 1.2-Gbps cell-bus (when used with chassis other than the Cisco MGX 8950)Cisco PXM-45/C used only as processor in Cisco MGX 8950; Cisco MGX-XM-60 provides switch-fabric function in that chassisHot swappable1:1 hot-standby redundancyUser-selectable primary and secondary clock sources with graceful switchoverInternal Stratum-3, external Building Integrated Timing Supply (BITS), or in-band clock sourcesIn-band or out-of-band management using EIA/TIA-232 or 10BASE-T control portsSupport for narrowband and broadband service modules scaling from DS-0 to OC-48c/STM-16 or DS-3/E3 to OC-192/STM-64 (depending on the chassis used)Chassis compatibilityCisco MGX 8830/B, MGX 8850, MGX 8850/B, MGX 8880, and MGX 8950Software compatibilityMinimum Cisco MGX software release supporting Cisco PXM-45/C:Cisco MGX 8850 Software Release 4.0.15Cisco MGX 8950 Software Release 4.0.15 Cisco MGX Software Release 5.0.20 (for Cisco MGX 8880 and MGX 8850/B)Cisco MGX Software Release 5.2.00 (for Cisco MGX 8830/B)Network Management Managed by Cisco WAN Manager Software suite Based on Simple Network Management Protocol (SNMP)PowerInput power required: -48 VDCPower consumption: 128 WPhysical DimensionsH x D: 15.75 x 16.5 in. (40.00 x 41.91 cm)Weight6.5 lbs

Key Features: The main features of the Cisco MGX 8800/8900 16-Port OC-3c/STM-1 ATM Switch Service Module are listed here.Full nonblocking, full-duplex line-rate throughput on all 16 portsHigh reliability with hot-standby 1+1 16-port ATM switch service module card redundancyPer-virtual-path and per-virtual-circuit traffic shaping and available bit rate (ABR) with virtual source and virtual destinationY-cable and APS (1:1 and 1+1) port redundancy, plus APS 1+1 card redundancyUp to 4 million cell buffersUp to 16 classes of service (CoS) that can be used to support IP or ATM servicesSupport for standards-based Private Network-to-Network Interface (PNNI), switched virtual circuit (SVC) and switched virtual path (SVP), soft permanent virtual connection (SPVC) and soft permanent virtual path (SPVP), and Multiprotocol Label Switching (MPLS) servicesChassis Compatibility: Cisco MGX 8830/B, MGX 8850, MGX 8850/B, and MGX 8950Software Compatibility: Cisco MGX 8800/8900 SW Release 5.0.20 and aboveProtocols : ATM and SONET/SDHPort Density : 16 portsNetwork Management Managed by Cisco WAN Manager software suite Based on Simple Network Management Protocol (SNMP)PowerInput power required: -48 VDCPower consumption: 114WPhysical DimensionsH x D: 15.83 x 15.65 in. (40.20 x 39.75 cm)Weight6.5 lb (2.95 kg)

AXSM can be used in the MGX 8850 to provide ATM capability up to OC-48c/STM-16.High scalability in interface speeds with T3/E3 ports, OC-3c/STM-1, OC-12c/STM-4, and OC-48c/ STM-16 AXSM modules. Each port on the AXSM can be configured for either trunk or access applications.Industry leading module port densities of 16 T3/E3 ports, 16 OC-3c/STM-1 ports, 4 OC-12c/STM-4 ports, and 1 OC-48c/ STM-16 port that can scale up to 12 OC-48c/STM-16 modules in each MGX 8850 Multiservice Switch. Each OC-48c/STM-16 delivers fully nonblocking, full duplex throughput, in which a connection can occupy the entire line rate.Support for all ATM service classes, with up to 16 classes of service (CoS). Supports carrier-class implementation of standards-based PNNI, SVC/SVP, SPVC/SPVP, and MPLS services. Large cell buffers (one million cells), which help to maximize "goodput" performance during congestion, reducing the number of retransmits; the buffers are allocated dynamically, depending on connection resource needs, thereby optimizing use of system resources.High reliability with hot-standby 1:1 AXSM card redundancy, 1:1 and 1+1 line redundancy using APS.Ports and trunks supported on same AXSM moduleUser-Network Interface (UNI) Specifications 3.0, 3.1, 4.0Network ManagementManagement using Cisco WAN Manager software suiteBased on Simple Network Management Protocol (SNMP)Physical SpecificationsDimensions: (H x D) 15.83 x 15.65 in.Electrical SpecificationsInput power required: -48 VDCPower consumption: 95W

ApplicationsHigh-density broadband ATMScaling MPLS servicesConvergence of voice and data networksTechnical SpecificationsThe following are some of the key features of the Cisco MGX 8950 Multiservice Switch:Scalability of up to 180-Gbps fully redundant nonblocking switching within a single chassis10-Gbps ATM interfaces (OC-192c/STM-64) Industry-leading broadband densityOC-3c/STM-1, OC-12c/STM-4, and OC-48c/STM-16 trunk aggregationIndustry's highest network availabilitySoftware compatibility MGX 4.0.15 release and later (depending on the service modules configured)Service module compatibilityAXSM-16-155-XG, AXSM-8-622-XG, AXSM-4-2488-XG, AXSM-1-9953-XGAXSM-16-T3E3/B, AXSM-1-2488/BMGX-RPM-PR-256, MGX-RPM-PR-512, MGX-RPM-XF-512Control cardPXM45/C Processor Switching Module (only processor function is used)Redundant slots 7 and 8 reserved for control cardSlotsControl processor slots: 2 fixed double-height slots for primary and secondarySwitching card slots: 2 fixed double-height slots divided into 4 single-height slots for 4 load-sharing XM60 switching cardsService module slots: 12 double-height slotsConnectivityT3/E3, OC-3/STM1, OC-12/STM-4, OC-48/STM-16, OC-192/STM-64, POS, Ethernet, Fast Ethernet, Gigabit EthernetNetwork management interfacesRJ-45 Ethernet port for the management interface at the node, and In-band ATM connection to reach remote node for management connectivity,DB-15 for the visual and audible alarm port, a command-line interface (CLI) for local management, Simple Network Management Protocol (SNMP) for the network management system interface, Secure File Transfer Protocol (SFTP) for file transfer,and Secure Shell (SSHv1 and SSHv2) Protocol for remote CLI accessPhysical dimensions(H x W x D): 35 x 19 x 22 inches (88.9 x 48.26 x 55.88 cm)Rack-mountable in 19- and 23-inch EIA/RETMA and ETSI racksPowerTypical consumption: 5 kW for maximum configuration system

Key FeaturesThe main features of the Cisco MGX 8950 OC-192c/STM-64 ATM Switch Service Module are listed here.Full nonblocking, full-duplex line-rate throughputHigh reliability with hot-standby 1+1 ATM switch service module card redundancyPer-virtual-path and per-virtual-circuit traffic shaping and available bit rate (ABR) with virtual source and virtual destinationUp to 4 million cell buffersUp to 16 classes of service (CoS) that can be used to support IP or ATM servicesSupport for standards-based Private Network-to-Network Interface (PNNI), switched virtual circuit (SVC) and switched virtual path (SVP), soft permanent virtual connection (SPVC) and soft permanent virtual path (SPVP), and Multiprotocol Label Switching (MPLS) servicesChassis Compatibility : Cisco MGX 8950Software Compatibility : Cisco MGX Software Release 4.0.15 and aboveProtocols : ATM and SONET/SDHPort Density : 1 portLayer 1 (Physical Layer) Feature SummaryUser-Network Interface (UNI) 3.0, 3.1, and 4.0 physical layer specificationsCompliance with the following SONET standards:Bellcore GR-253-COREANSI T1.105Compliance with the following SDH standards:ITU-T G.707, G.708, G.709, and G.783ITU-T G.957 and G.958Additional Physical Layer Specifications for Ports and OpticsNetwork Management : Managed by Cisco WAN Manager software suiteBased on Simple Network Management Protocol (SNMP)Power : Input power required: -48 VDCPower consumption: 205WPhysical Dimensions : H x D: 15.83 x 15.65 in. (40.20 x 39.75 cm)Weight : 6.5 lb (2.95 kg)

Industrial  outdoor 802.11ac wireless.Designed and certified for extreme environments.Rail - rolling stock  shock and vibration certified.Chipset with best-in-class RF architecture.SoftwareCisco Unified Wireless Network Software Release with AireOS Wireless Controllers:8.0.120.0 or later for the Cisco IW3700 Series Access PointCisco IOS Software Release 15.3(3)JA5 or later for the Cisco IW3700 Series Access Point802.11ac Wave 1 capabilities  4 x 4 MIMO with 3 spatial streams  Maximal-Ratio Combining (MRC)  802.11ac beamforming  20- 40- and 80-MHz channels  PHY data rates up to 1.3 Gbps (80 MHz with 5 GHz)  Packet aggregation: A-MPDU (Tx/Rx) A-MSDU (Tx/Rx)  802.11 Dynamic Frequency Selection (DFS)  Cyclic Shift Diversity (CSD) support802.11n version 2.0 (and related) capabilities4 x 4 MIMO with 3 spatial streams  Maximal-Ratio Combining (MRC) 802.11n and 802.11a/g beamforming  20- and 40-MHz channels PHY data rates up to 450 Mbps (40 MHz with 5 GHz) Packet aggregation: A-MPDU (Tx/Rx) A-MSDU (Tx/Rx) 802.11 Dynamic Frequency Selection (DFS) Cyclic Shift Diversity (CSD) supportData rates supported802.11a: 6  9  12  18  24  36  48  and 54 Mbps802.11g: 1  2  5.5  6  9  11  12  18  24  36  48  and 54 MbpsInterfaces 10/100/1000BASE-T autosensing (M12 8P female connector with X-coding per IEC 61076-2) PoE In (802.3af) PoE+ In (802.3at) 10/100/1000BASE-T autosensing (M12 8P female connector with X-coding per IEC 61076-2) PoE Out (802.3af) Management console port (serial with RJ-45 connector)Indicators Status LED indicates boot loader status  association status  operating status  boot loader warnings  boot loader errorsSystem memory 512 MB DRAM 64 MB flashDimensions (W x L x H) Access point (not including connectors): 11.3 x 8.0 x 2.3 in (28.7 x 20.3 x 5.9 cm) Volume: 148 cubic inches (2.4 liters)Weight  6.7 lb (3.0 kg)Warranty5-year limited hardware warranty

For small campus deployments with the flexibility of copper or fiber uplinksUp to 250 APs  5000 clients  and 5-Gbps throughputHot patching  time saving and hitless upgradesAdvanced  on demand telemetryThe Cisco Catalyst 9800-L is a fixed wireless controller with seamless software updates for small and midsize enterprises.Built from the ground up for intent-based networking  the Cisco Catalyst 9800 L brings togetherCisco IOS XE Software and Cisco RF excellence to create a best in-class wireless experience for your evolving and growing organizationThe Cisco Catalyst 9800-L is feature rich and enterprise ready to power your business-critical operations and transform end-user experiences:Choose between copper and fiber uplinks. This choice gives you flexibility in your network.High availability and seamless software updates  enabled by hot and cold patching  keep your clients and services always on in planned and unplanned events.Secure the air  devices  and users with the Cisco Catalyst 9800-L. The wireless infrastructure becomes the strongest first line of defense  with Encrypted Traffic Analytics and Software-Defined Access (SD-Access). The controller comes with built-in security: Secure Boot  runtime defenses  image signing  integrity verification  and hardware authenticity.Built on a modular operating system  the controller features open and programmable APIs that enable automation of day-0 to day-N network operations. Model-driven streaming telemetry provides deep insights into your network and client health.Maximum number of access points:250  500 (with performance license)Maximum number of clients : 5000  10000 (with performance license)Maximum throughput : 5 Gbps  10 Gbps(with performance license)Maximum WLANs : 4096Maximum VLANs : 4096Fixed uplinks : 2x 10G/Multigigabit copper or 2x 10G/Multigigabit fiberPower supply : 110W  12VDC  AC/DC adapterMaximum power consumption : 9800-L-C: 86.9W (with 4.5W USB load) / 9800-L-F: 84.5W (assumes 2pc 2.5W SFP and with 4.5W USB load)Deployment modes : Centralized  Cisco FlexConnect  and fabric Form factor : 1RU; half-width chassis allows side-by-side installation in standard 19-in. rackLicense : Smart License enabledSoftware : Cisco IOS XEManagement : Cisco DNA Center  Cisco Prime Infrastructure  and third party (open standards APIs)Interoperability : AireOS-based controllersAccess points : Cisco Aironet 802.11ac Wave 1 and Wave 2 access points  Cisco Catalyst 9100 802.11ax access pointsDimesnsion : Width : 8.5 in. (21.59 cm) Depth : 9.06 in. (23.01 cm)Height : 1.58 in. (4.02 cm)Weight : C9800-L-C: 3.95 lb. (1.79 kg)C9800-L-F: 4.01 lb. (1.82 kg)

For medium-sized campus deploymentsUp to 2000 APs  32 000 clients  and 40-Gbps throughputHot patching  time saving and hitless upgradesAdvanced  on-demand telemetry High availability and seamless software updates  enabled by hot and cold patching  keep your clients and services always on during planned and unplanned events.Secure air  devices  and users with the Cisco Catalyst 9800-40. Wireless infrastructure becomes the strongest first line of defense with Cisco Encrypted Traffic Analytics (ETA) and Software-Defined Access (SD-Access). The controller comes with built-in security: secure boot  runtime defenses image signing  integrity verification  and hardware authenticity.Built on a modular operating system  the 9800-40 features open and programmable APIs that enable automation of day-0 to day-N network operations. Model-driven streaming telemetry provides deep insights into the health of your network and clients.Maximum number of access points : Up to 2000Maximum number of clients : 32 000Maximum throughput : Up to 40 GbpsMaximum WLANs : 4096Maximum VLANs : 4096Max Site Tags : 2000Max Flex APs per Site : 100Max Policy Tags : 2000Max RF Tags : 2000Max RF Profiles : 4000Max Policy Profiles : 1000Max Flex Profiles : 2000Interfaces : 4x 10 GE/1 GE SFP+/SFPPower supply : AC power with optional redundant AC powerMaximum power consumption : 381WDeployment modes : Centralized  Cisco FlexConnect  and Fabric Wireless (SD-Access)Form factor:1RULicense : Smart License enabledOperating system : Cisco IOS XEManagement : Cisco DNA Center  Cisco Prime Infrastructure  integrated WebUI  and third party (open standards APIs)*Interoperability ; AireOS-based controllers*Policy engine : Cisco Identity Services Engine (ISE)*Location Platform : Cisco Connected Mobile Experiences (CMX)/ Cisco DNA Spaces *Access points : Aironet 802.11ac Wave 1 and Wave 2 access points  Catalyst 9100 802.11ax access pointsWidth : 17.3 inches (43.94 cm)Depth : 19.5 inches (49.53 cm)Height : 1.72 inches (4.37 cm)Weight : 22.8 lb (10.34 kg)Hard Disk Drives (HDD) :  SATA Solid-State Drive (SSD)240GB of memory

High availability and seamless software updates  enabled by hot patching  keep your clients and services always on in planned and unplanned events.Secure air  devices  and users with the Cisco Catalyst 9800-80. Wireless infrastructure becomes the strongest first line of defense with Cisco Encrypted Traffic Analytics (ETA) and Software-Defined Access (SD-Access).The controller comes with built-in security: secure boot  runtime defenses  image signing  integrity verification  and hardware authenticity.Built on a modular operating system  the 9800-80 features open and programmable APIs that enable automation of day-0 to day-N network operations.Model-driven streaming telemetry provides deep insights into the health of your network and clients.Maximum number of access points : Up to 6000Maximum number of clients : 64 000Maximum throughput : Up to 80 GbpsMaximum WLANs : 4096Maximum VLANs : 4096Max site tags : 6000Max Flex APs per site : 100Max policy tags : 6000Max RF tags : 6000Max RF profiles : 12000Max policy profiles : 1000Max flex profiles : 6000Fixed uplinks : 8x 10 GE or 6x 10 GE + 2x 1 GE SFP+/SFPModular uplinks (optional)The supported uplink modules are C9800-18X1GE(=) C9800-10X10GE(=) C9800-1X40GE(=) C9800-2X40GE(=) C9800-1X100GE(=)The uplink modules are hot-swappable.Supports 10 GE  40 GE  and 100 GE QSFP transceiversRedundant power supply : AC or DC power supplyMaximum power consumption with modules 600WDeployment modes : Centralized  Cisco FlexConnect®  and Fabric Wireless (SD-Access)Form factor : 2RULicense : Smart License enabledOperating system : Cisco IOS XEManagement : Cisco DNA Center  Cisco Prime Infrastructure  integrated WebUI  and third party (open standards APIs)Interoperability : AireOS-based controllersPolicy engine : Cisco Identity Services Engine (ISE)Location platform : Cisco Connected Mobile Experiences (CMX)/Cisco DNA Spaces*Access points : Aironet 802.11ac Wave 1 and Wave 2 access points  Catalyst 9100 802.11ax access pointsWidth : 17.3 inches (43.94 cm)Depth : 20.5 inches (52.07 cm)Height : 3.47 inches (8.81 cm)Weight : 31.5 lb (14.29 kg)Hard Disk Drives (HDD) :   SATA solid-state drive (SSD) 240 GB of memory

Deploy in private or public (AWS) cloudUp to 6000 APs and 64 000 clientsHot patching  time saving and hitless upgradesAdvanced  on-demand telemetryHigh availability and seamless software updates  enabled by hot and cold patching  keep your clients and services always on in planned and unplanned events.Secure air  devices  and users with the Cisco Catalyst 9800-CL. Wireless infrastructure becomes the strongest first line of defense with Cisco Encrypted Traffic Analytics (ETA) and Software-Defined Access (SD-Access). The controller comes with built-in security: runtime defenses  image signing and integrity verification. Deploy anywhere to enable wireless connectivity everywhere. Whether in a public or private cloud  the Cisco Catalyst 9800-CL best meets your organization’s needs.Built on a modular operating system  the 9800-CL features open and programmable APIs that enable automation of day-0 to day-N network operations. Model-driven streaming telemetry provides deep insights into the health of your network and clients.Maximum number of access points : Up to 6000Maximum number of clients : 64 000Maximum throughput : Up to 2.2 Gbps*Maximum WLANs : 4096Maximum VLANs : 4096Deployment modes : Centralized  Cisco FlexConnect and Fabric Wireless (SD-Access)License : Smart License enabledOperating system : Cisco IOS XE SoftwareManagement : Cisco DNA Center  Cisco Prime Infrastructure  integrated WebUI  and third party (open standards APIs)Interoperability : AireOS-based controllersPolicy engine : Cisco Identity Services EngineLocation platform : Cisco Connected Mobile Experiences (CMX) / DNA SpacesAccess points : Aironet 802.11ac Wave 1 and Wave 2  Catalyst 9100 802.11ax access points

Catalyst 9800 embedded on a Catalyst 9100 access pointIdeal for distributed branches and small campusesUp to 100 APs and 2 000 clientsHot patching  time saving and hitless upgradesThe Cisco Embedded Wireless Controller on Catalyst® Access Points (EWC-AP) is the next-generation Wi-Fi solution  combining the most advanced controller – the Cisco Catalyst 9800 Series Wireless Controllers – with the latest Wi-Fi 6 access points – the Cisco Catalyst 9100 Access Points – creating a best-in-class wireless experience for your evolving and growing organization.With the 9800 Series wireless controller embedded on the Cisco Catalyst 9100 Access Points  organizations can now benefit from enterprise-class resiliency  security  and IT simplicity for single or multisite enterprise deployments.Built for intent-based networking and Cisco DNA  the EWC-AP helps you simplify complexity  optimize IT  and reduce operational costs by leveraging intelligence  automation  and human expertise that no other vendor can deliver  regardless of where you are in the intent-based networking journey.Maximum number of access points : Up to 100Maximum number of clients : Up to 2000Maximum number of WLANs :16Deployment modes:Cisco FlexConnect®Maximum FlexConnect APs per site :100License :Smart License enabledOperating system : Cisco IOS® XE SoftwareManagement : Cisco DNA Center 1.3.2  integrated WebUI  mobile app  and third party (open standards APIs)Policy engine : Cisco Identity Services Engine (ISE) 2.2  2.3  and 2.4Access points : Cisco Catalyst 9100 Access Points and Aironet® 802.11ac Wave 2 access points (operating in client serving mode only)Warranty information : The Cisco Embedded Wireless Controller on Catalyst Access Points comes with a limited lifetime warranty that provides full warranty coverage of the hardware for as long as the original end user continues to own or use the product. The warranty includes 10-day advance hardware replacement and ensures that software media are defect-free for 90 days. For more details Your embedded software is subject to the Cisco End User License Agreement (EULA) (link available below) and/or any Supplemental EULA (SEULA) or specific software warranty terms for additional software products loaded on the device.SecurityRogue detection  classification  and containment802.1X supplicant support on EWC-APWalled garden and DNS ACLsManagementCisco DNA Center for Automation and AssuranceDashboard (web browser) and easy-to-use mobile app for deploying  provisioning  and monitoringStandards-based interoperability tools using programmable interfacesOpen standards-based programmability with NETCONF and YANGGuestCentral web authentication  local web authentication  and BYODCisco DNA Spaces integration for personalized and relevant guest experience

Brand : Cisco Systems, Inc. Series : 350 Model : SF350-48-K9-NA Format : Desktop Network Management Type : Ethernet Switch Uplink Ports: Yes Uplink Interface : SFP Primary Ports : 48 x Fast Ethernet Network Fast Ethernet Gigabit Ethernet 2 x Gigabit Ethernet Expansion Slot 4 x Gigabit Ethernet Network Primary Port Speed: 10/100Base-TX 1000Base-X 10/100/1000Base-TX Data Transmission Speed :  SFP Weight : 10.4

Brand : Cisco Systems, Inc. Series : 350 Model : SF350-48P-K9-NA Format : Desktop Network Management Type : Ethernet Switch Uplink Ports : Yes Uplink Interface : SFP Primary Ports : 48 x Fast Ethernet Network Fast Ethernet 4 x Gigabit Ethernet Expansion Slot Gigabit Ethernet 2 x Gigabit Ethernet Network Primary Port Speed : 10/100Base-TX 1000Base-X 10/100/1000Base-TX Data Transmission Uplink Speed : SFP Weight : 15.9

Brand : Cisco Systems, Inc. Series : 350 Model : SF350-48MP-K9-NA Format : Desktop Network Management Type : Ethernet Switch Uplink Ports : Yes Uplink Interface : SFP Primary Ports : 48 x Fast Ethernet Network Fast Ethernet Gigabit Ethernet 4 x Gigabit Ethernet Expansion Slot 2 x Gigabit Ethernet Network Primary Port Speed : 10/100Base-TX 1000Base-X 10/100/1000Base-TX Data Transmission Uplink Speed : SFP Weight : 16.2 Model : SF350-48MP

Part Number N9K-C92160YC-XPorts : 48 x 10- and 25-Gbps SFP+ and 6 QSFP+ ports (4 are 100-Gbps capable)Supported speeds :1, 10, and 25 Gbps on SFP+ ports10, 25, 40, and 100 Gbps on QSFP+ portsPort configuration :48 x 10/25-Gbps ports for downlinks; 4 of the 6 uplink ports are 100-Gbps capable. Ports 50 and 52 can beindividually configured into 1 x 100 Gbps, 4 x 10 Gbps, 4 x 25 Gbps, 1 x 40 Gbps, or 2 x 50 GbpsCPU :2 coresSystem memory : 16GSSD drive :24GShared system buffer :20MBManagement ports 2 ports: 1 RJ-45 and 1SFPUSB ports 1RS-232 serial ports :  1Power supplies (up to 2) :650W AC, 930W DC, or 1200W AC/HVDCPhysical dimensions :(H x W x D)1.72 x 17.3 x 22.5 in. (4.4 x 43.9 x 57.1 cm)Weight (without power supplies or fans)14.12 lb (6.4 kg)(1) Power Supply (2) 4 x Fan Module (3) Power Supply(4) Out-of-band management port (RJ-45 port)(5) Chassis LEDs (Beacon [BCN] and Status [STS])(6) USB port used for saving or copying functions (7) Out-of-band management port (SFP port)(8) Console port (RS232 port)

N9K-C92160YC-X is one of the Cisco Nexus 9200 switches. 92160YC-X Switch is optimized for Cisco NX-OS deployments. It provides 48 1/10/25-Gb host ports and up to six hybrid uplink ports that can be configured as 10, 25, 40, or 100-Gb ports. With 3.2 Tbps of switching capacity, the92160YC-X delivers line-rate Layer 2 and 3 features for demanding enterprise, service provider hosting, and cloud computing environments.

The Cisco Nexus 92304QC switch (N9K-C92304QC) is a 2-RU switch with the following ports:56 fixed 40-Gigabit QSFP+ (optical) interface ports supporting 1-, 10-, and 40-Gigabit speeds16 of these ports support breakout cables for connections to 64 1- and 10-Gigabit ports on other devices.8 QSFP28 ports supporting 40- and 100-Gigabit speeds1 console port1 management port2 software-defined ports (labeled as S1-65 and S1-66)1 USB port

The Cisco Nexus 93360YC-FX2 Leaf Switch is a 2-Rack-Unit (2RU) Leaf switch that supports 7.2 Tbps of bandwidth and 2.8 bpps across 96 fixed 10/25G SFP+ ports and 12 fixed 40/10G QSFP28 ports. The 96 ports of downlinks support 1/10/25-Gbps. The 12 uplinks ports can be configured as 40- and 100-Gbps ports, offering flexible migration options. The switch is ideal for a non-oversubscribed solution in a compact form factor. The switch has FC-FEC and RS-FEC enabled for 25Gbps support over longer distances.Main FeaturesFX2SwitchL3managed96 x 1/10/25 Gigabit SFP+ + 12 x 40/100 Gigabit QSFP28rack-mountableBuilt-in Devices :128 GB SSDInstalled Size :16 GBCapacity :SPAN sessions: 4, Port channels: 512, VLANs supported: 3967, NAT entries: 1023, HSRP groups: 490, Longest prefix match (LPM) routes: 896000, Multicast routes: 32000, ACL entries (ingress): 5000, MST instances: 64, ECMP paths: 64, IP host entries: 896000, ACL entries (egress): 2000, MAC addresses: 256000, Rapid Per-VLAN Spanning Tree Plus instances: 3967Form Factor :Rack-mountablePorts Qty :96Advanced Switching :Layer 3Routing Protocol :ECMP, RSVP, BGP, PIM-SM, MSDP, OSPF, EIGRP, RIP, RIP-2, Multiprotocol BGP, HSRP, MPLSManageable :YesStatus Indicators :StatusFeatures :Layer 3 switching, Open Shortest Path First (OSPF), 3 fans, Port-side exhaust (PSE), Multicast Source Discovery Protocol (MSDP), MPLS support, Virtual Extensible LAN (VXLAN), MACsec support, Source-Specific Multicast (SSM), Access Control List (ACL) support, Virtual PortChannel (vPC) technology, 40MB system buffer, Spanning Tree Protocol (STP) support, Power On Auto Provisioning (POAP), Ethernet Virtual Private Network (EVPN), Multiple Spanning Tree Protocol (MSTP) supportInterfaces :1 x management SFP+, 12 x 100Gbit/40Gbit LAN QSFP28, 96 x 1/10/25Gbit LAN SFP+, 1 x serial (RS-232), 1 x USB, 1 x management RJ-45Ports Type :40/100 Gigabit QSFP28Dimensions & WeightWidth :17.4 inchDepth :22.9 inchHeight :3.4 inch

The Cisco Nexus 9336C-FX2 offers flexible port speeds in a compact form factor. Designed to meet the changing needs of data centers, big data applications, and automated cloud environments, this powerful switch delivers superior programmability.Main Features : FX2SwitchL3managed36 x 100 Gigabit QSFP28 / 40 Gigabit QSFP28rack-mountableBuilt-in Devices :128 GB SSDInstalled Size :24 GBPerformance :Bandwidth: 2.8 bpps, Bandwidth: 7.2 TbpsFeatures :Ethernet Virtual Private Network (EVPN), Port exhaust, 40MB system buffer, Spanning Tree Protocol (STP) support, Virtual PortChannel (vPC) technology, Multiple Spanning Tree Protocol (MSTP) support, Power On Auto Provisioning (POAP), 3 fan trays, Side intake airflow, Virtual Extensible LAN (VXLAN), Source-Specific Multicast (SSM), Access Control List (ACL) support, MACsec supportType :100 Gigabit QSFP28 / 40 Gigabit QSFP28Interfaces :1 x management RJ-45, 1 x USB, 36 x 100Gbit/40Gbit LAN QSFP28, 1 x management SFP+, 1 x serial (RS-232)Type :Internal power supplyPower Redundancy :OptionalInstalled Qty :0Max Supported Qty :2Nominal Voltage :AC 120/230 VFrequency Required :50/60 hertzPower Consumption Operational :777 wattDimensions & WeightWidth :17.3 inchDepth :24.5 inchHeight :1.7 inchWeight :18.74 lbs

Architectural flexibility : Support for Cisco ACI architecture and NX-OS48 x 1/10/25 Gbps fiber ports12 x 40/100 Gbps QSFP28 portsSupports 4.8 Tbps of bandwidth and over 1.8 bppsRich features : Automated, policy-based systems management with Cisco ACIBuild programmable SDN fabrics leveraging open APIs and over 65 Cisco ACI global technology partnersEnhanced Cisco NX-OS Software designed for performance, resiliency, scalability, manageability, and programmabilityReal-time buffer utilization per port and per queue, for monitoring traffic micro-bursts and application traffic patternsHighly available and efficient design : High-performance, Layer 2 and 3 non-blocking architectureEasily deployed into either a hot-aisle or cold-aisle configurationRedundant, hot-swappable power supplies and fan traysSpecifications at a Glance : Powered by cloud-scale technology48 x 1/10/25 Gbps fiber ports12 x 40/100 Gbps QSFP28 ports40 MB bufferUp to 4.8 Tbps of bandwidth

The Cisco Nexus 9348GC-FXP Switch is a 1RU switch that supports 696 Gbps of bandwidth and over 250 mpps. The 48 1GBASE-T downlink ports on the switch can be configured to work as 100-Mbps, 1-Gbps ports. The 4 ports of SFP28 can be configured as 1/10/25-Gbps and the 2 ports of QSFP28 can be configured as 40- and 100-Gbps ports.Cisco Nexus 9348GC-FXP Switch is designed to meet the changing needs of data centers, big data applications, and automated cloud environments.Highlights points: Powered by Cisco Cloud Scale ASIC technologySupport for Cisco NX OS Software and Cisco ACI (Application Centric Infrastructure) architectureHigh-performance, Layer 2 and 3 non-blocking architectureEasily deployed into either a hot-aisle or cold-aisle configurationCisco Tetration Analytics Platform support with built-in hardware sensors for rich traffic flow telemetry and line-rate data collectionCisco Nexus Data Broker support for network traffic monitoring and analysisRobust hardware system specifications feature 4-core CPU, 24 GB of system memory, and respectively 128-GB SSD driveThe 40-MB buffer supporting highly scalable data centers and big data applications 696 Gbps of bandwidth and over 250 mppsFixed downlinks with 48 x FE/GEFixed uplinks with 4 x 25GE SFP28, 2 x 100GE QSFP28

Physical : 64-port 40/100G QSFP28 ports & 2-port 1/10G SFP+ ports1200 watt (W) AC power supplies or 930W DC power supplies (up to 2)Hot-swappable, dual fan trays with redundant fansSystem memory: 32GBSSD: 256GBUSB: 1 portRS-232 serial console ports: 1(1) 1-/10-Gigabit SFP+ ports (2)(2) 40-/100-Gigabit QSFP28 ports (ports 1 to 48 in 4 rows of 12 ports)(3) Green colored 40-/100-Gigabit QSFP28 ports supporting MACsec (when software support is available) (ports 49 to 64 in 4 rows of 4 ports)(4) Fan modules (3) with slots numbered from 1 (left) to 3 (right)(5) USB port (1)(6) Management port (1—SFP optical port)(7) Management port (1—RJ-45 copper port)(8) Power supply modules (1 or 2) (AC power supplies shown) with slots numbered 1 (top) and 2 (bottom)(9) Console port (1)Management ports:2 (1 x 10/100/1000BASE-T and 1 x 1-Gbps SFP+)Broadwell-DE CPU: 4 coresPhysical (H x W x D) 3.38 x 17.37 x 22.27 in. (8.59 x 44.13 x 56.58 cm)Weight (chassis) 36.9lb (16.74kg) with power supplies and fans, 27.4 lb (12.43kg) without power supplies and fans

Ports :32 QSFP+ portsSupported speeds :40 Gigabit Ethernet speedsPhysical: (H x W x D) 1.72 x 17.3 x 22.5 in. (4.4 x 43.9 x 57.1 cm)Weight 22 lb (10.0 kg) (without power supplies or fans)Predictable highperformance : Latency of 1 to 2 microseconds with up to 1.28 Tbps of bandwidth enables customers to build a robust switch fabric scalingfrom as few as 200 10-Gbps server ports to more than 200,000 10-Gbps server ports.Increased integrated buffer space : Up to a total of 50 MB of integrated shared buffer space allows better management of speed mismatch between access anduplink ports.Designed for availability : Hot-swappable, redundant power supplies and fan trays increase availability.Flexible airflow configuration: Port-side intake and port-side exhaust airflow configurations are both supported.CPU, SSD,and memory : Dual-core 2.5-GHz x86 CPUs with 64-GB SSD drive and 16 GB of memory provide enhanced network performance.Power efficiency : All Cisco Nexus 9000 Series power supplies are 80 Plus Platinum rated.Advanced optics : Cisco offers a pluggable 40 Gigabit Ethernet QSFP+ transceiver that enables customers to use existing 10 Gigabit Ethernetdata center cabling to support 40 Gigabit Ethernet connectivity. This technology facilitates adoption of 40 Gigabit Ethernetwith no cable infrastructure upgrade cost.

Ports :32 QSFP+ portsSupported speeds :40 Gigabit Ethernet speedsPhysical: (H x W x D) 1.72 x 17.3 x 22.5 in. (4.4 x 43.9 x 57.1 cm)Weight 22 lb (10.0 kg) (without power supplies or fans)Predictable highperformance : Latency of 1 to 2 microseconds with up to 1.28 Tbps of bandwidth enables customers to build a robust switch fabric scalingfrom as few as 200 10-Gbps server ports to more than 200,000 10-Gbps server ports.Increased integrated buffer space : Up to a total of 50 MB of integrated shared buffer space allows better management of speed mismatch between access anduplink ports.Designed for availability : Hot-swappable, redundant power supplies and fan trays increase availability.Flexible airflow configuration: Port-side intake and port-side exhaust airflow configurations are both supported.CPU, SSD,and memory : Dual-core 2.5-GHz x86 CPUs with 64-GB SSD drive and 16 GB of memory provide enhanced network performance.Power efficiency : All Cisco Nexus 9000 Series power supplies are 80 Plus Platinum rated.Advanced optics : Cisco offers a pluggable 40 Gigabit Ethernet QSFP+ transceiver that enables customers to use existing 10 Gigabit Ethernetdata center cabling to support 40 Gigabit Ethernet connectivity. This technology facilitates adoption of 40 Gigabit Ethernetwith no cable infrastructure upgrade cost

Device Type : Switch - 36 ports - L3 - managedEnclosure Type : Desktop, rack-mountable 2USubtype : 40 Gigabit EthernetPorts : 36 x 40 Gigabit QSFP+Performance : Bandwidth: 1.44 TbpsCapacity : Longest prefix match (LPM) entries (IPv4): 16000 ¦ Host table entries (IPv4): 88000 ¦ MAC addresses: 160000 ¦ IPv4 routes (Multicast): 32000 ¦ Virtual interfaces (VLANs): 4096 ¦ Equal-Cost Multipathing (ECMP) ways: 64 ¦ Multiple Spanning Tree Protocol instances: 64 ¦ Rapid Per-VLAN Spanning Tree Plus instances: 507 ¦ Virtual Routing and Forwarding (VRF) entries: 1000 ¦ IGMP snooping entries: 32000Jumbo Frame Support : YesRouting Protocol : IS-IS, BGP, EIGRP, HSRP, VRRP, OSPFv2, PIM-SM, OSPFv3, MSDP, static IPv4 routing, ECMP, Bidirectional Forwarding Detection (BFD), VRRPv3Remote Management Protocol :SNMP 1, SNMP 2, RMON, Telnet, SNMP 3, SSH-2Authentication Method : RADIUS, PAP, CHAP, TACACS+, MS-CHAP, MS-CHAP v.2Features : Flow control, modular design, load balancing, VLAN support, IGMP snooping, Syslog support, Weighted Round Robin (WRR) queuing, Broadcast Storm Control, Multicast Storm Control, Unicast Storm Control, Weighted Random Early Detection (WRED), Spanning Tree Protocol (STP) support, Rapid Spanning Tree Protocol (RSTP) support, Multiple Spanning Tree Protocol (MSTP) support, Access Control List (ACL) support, Quality of Service (QoS), RADIUS support, RDMA support, Virtual Route Forwarding-Lite (VRF-Lite), Uni-Directional Link Detection (UDLD), Rapid Per-VLAN Spanning Tree Plus (PVRST+), LLDP support, DHCP relay, Link Aggregation Control Protocol (LACP), Virtual Routing and Forwarding (VRF), Class of Service (CoS), DiffServ Code Point (DSCP) supportCompliant Standards : IEEE 802.3z, IEEE 802.1D, IEEE 802.1Q, IEEE 802.1p, IEEE 802.3x, IEEE 802.3ad (LACP), IEEE 802.1w, IEEE 802.3ae, IEEE 802.1s, IEEE 801.1p, IEEE 802.1ab (LLDP), IEEE 802.3ba

Product Type :  Ethernet SwitchInterfaces/PortsTotal Number of Network Ports :  48Uplink Port :  YesModular  : YesStack Port : NoPort/Expansion Slot Details : 48 x 10 Gigabit Ethernet NetworkPort/Expansion Slot Details :6 x 100 Gigabit Ethernet Expansion SlotMedia & PerformanceMedia Type Supported Optical FiberMedia Type Supported Twisted PairEthernet Technology 100 Gigabit EthernetEthernet Technology 10 Gigabit EthernetNetwork Technology 100GBase-XNetwork Technology 10GBase-TI/O ExpansionsNumber of Total Expansion Slots  : 6Expansion Slot Type :QSFP28Shared SFP Slot :NoNetwork & Communication : Layer Supported :  3Management & ProtocolsManageable  : YesPower Description : Power Source Power SupplyRedundant Power Supply Supported  : Yes

N9K-C93108TC-EX is one of the Cisco Nexus 9300-EX switches. Cisco Nexus 9300-EX platforms are the next generation of fixed Cisco Nexus9000 Series Switches. The new platforms support cost-effective cloud-scale deployments, an increased number of endpoints, and cloud serviceswith wire-rate security and telemetry. The platforms are built on modern system architecture designed to provide high performance and meetthe evolving needs of highly scalable data centers and growing enterprises.Ports :  48 x 10GBASE-T and 6 x 40/100-Gbps QSFP28 portsDownlink supported speeds :  100-Mbps and 1/10-Gbps speedsCPU : 4 coresSystem memory : 24 GBSSD drive : 64 GBSystem buffer  : 40 MBManagement ports 2 ports: 1 RJ-45 and 1 SFPUSB ports  : 1RS-232 serial ports : 1Power supplies (up to 2) :  650W AC, 930W DC, or 1200W HVAC/HVDCTypical power (AC/DC) :  290WMaximum power (AC/DC) : 499WPhysical dimensions(H x W x D)1.72 x 17.3 x 22.5 in.(4.4 x 43.9 x 57.1 cm)Weight (without power supplies or fans) 17.7 lb (8.0 kg)

Ports : 96 fixed 1/10GBASE-T and 6 QSFP+ portsSupported speeds :100 Megabit Ethernet and 1/10 Gigabit Ethernet speeds40 Gigabit Ethernet uplinkports : 6 fixed QSFP+ portsPhysical (H x W x D) 3.5 x 17.5 x 22.5 in. (8.9 x 44.5 x 57.1 cm)Weight 26 lb (11.8 kg) (without power supplies, fans, or uplink module)Predictable high performance : Latency of 1 to 2 microseconds with up to 1.28 Tbps of bandwidth enables customers to build a robust switch fabric scalingfrom as few as 200 10-Gbps server ports to more than 200,000 10-Gbps server ports.Increased integrated buffer space : Up to a total of 50 MB of integrated shared buffer space allows better management of speed mismatch between access anduplink ports.Designed for availability : Hot-swappable, redundant power supplies and fan trays increase availability.Flexible airflow configuration :Port-side intake and port-side exhaust airflow configurations are both supported.CPU, SSD, and memory : Dual-core 2.5-GHz x86 CPUs with 64-GB SSD drive and 16 GB of memory provide enhanced network performance.Power efficiency : All Cisco Nexus 9000 Series power supplies are 80 Plus Platinum rated.Advanced optics : Cisco offers a pluggable 40 Gigabit Ethernet QSFP+ transceiver that enables customers to use existing 10 Gigabit Ethernetdata center cabling to support 40 Gigabit Ethernet connectivity. This technology facilitates adoption of 40 Gigabit Ethernetwith no cable infrastructure upgrade cost.

Brand:Cisco Small Business Series:300 Series Model:SRW2048-K9-NA Format:Rackmount Mac Address Table:8k Network Managed Type:Managed Dimensions:17.35 x 17.3 x 1.75 inch Weight:8.62 lbs

orm Factor:external Type:Wireless access point Connectivity Technology:wireless Type:Wireless access point Connectivity Technology:wireless Data Link Protocol:IEEE 802.11a, IEEE 802.11ac Wave 2, IEEE 802.11b, IEEE 802.11g, IEEE 802.11n Wireless Protocol:802.11a/b/g/n/ac Wave 2 Data Transfer Rate:5.2 Gbps Wi-Fi Bands: 2.4 GHz, 5 GHz Status Indicator:Boot state, error, status

Subcategory: power converters, splitters and accessories Manufacturer:Cisco Form Factor:external Product Line:Cisco Aironet Model:Power Injector

Brand : Cisco Systems, Inc. Series : 350 Model : SF350-48MP-K9-NA Format : Desktop Network Management Type : Ethernet Switch Uplink Ports : Yes Uplink Interface : SFP Primary Ports : 48 x Fast Ethernet Network Fast Ethernet Gigabit Ethernet 4 x Gigabit Ethernet Expansion Slot 2 x Gigabit Ethernet Network Primary Port Speed : 10/100Base-TX 1000Base-X 10/100/1000Base-TX Data Transmission Uplink Speed : SFP Weight : 16.2 Model : SF350-48MP

Device Type    : Switch - 48 ports - L3 - ManagedEnclosure Type     :Rack-mountable 1USubtype    :25 Gigabit Ethernet / 32Gb Fibre ChannelPorts    :48 x 1/10/25 Gigabit Ethernet / 8/16/32Gb Fiber Channel / FCoE SFP+ + 6 x 40/100 Gigabit QSFP28 / FCoEPerformance    :Bandwidth: 3.6 TbpsActive SPAN sessions: 4Capacity:     Multiple Spanning Tree Protocol instances: 64HSRP groups: 490Per VLAN Rapid Spanning Tree instances: 4000Maximum number of links in a port channel: 32Maximum number of port channels: 512ECMP paths: 64Virtual Routing and Forwarding (VRF) instances: 16000VLANs supported: 4096ACL entries (egress): 2000IGMP snooping groups: 32000Multicast routes: 32000Latency: < 1 µsMAC Address Table Size : 512K entriesRouting Protocol    : OSPF, RIP, RIP-2, BGP, EIGRP, HSRP, PIM-SM, MSDP, ECMP, MPLSFeatures:    Spanning Tree Protocol (STP) support, Multiple Spanning Tree Protocol (MSTP) support, Access Control List (ACL) support, Virtual PortChannel (vPC) technology, MACsec support, 4 fans, Virtual Extensible LAN (VXLAN), Source-Specific Multicast (SSM), Ethernet Virtual Private Network (EVPN), 40MB system buffer, Power On Auto Provisioning (POAP)Compliant Standards :     IEEE 802.1aeRAM :    64 GBBuilt-in Devices : 128 GB SSDInterfaces    48 x 1/10/25Gbit LAN / 8/16/32Gb Fibre Channel SFP+ downlink6 x 100Gbit/40Gbit LAN QSFP28 uplink1 x management RJ-451 x USB1 x serial (RS-232)

Embed resilient Cisco WiFi into your hardware.Extend intent-based networking to your solutions .IOx support for intelligence at the edge.Cisco DNA Assurance for worry-free network management.Radio type2.4 GHz: 802.11b/g/n  2x2 MIMO  2 spatial streams5 GHz: 802.11a/n/ac  2x2 MIMO  2 spatial streams802.11ac Wave 2 capabilities 2x2 MIMO with two spatial streams  Multi- and single-user MIMO  Maximal-Ratio Combining (MRC)  802.11ac beamforming (transmit beamforming)  20- 40- and 80-MHz channels  PHY data rates up to 867 Mbps (80-MHz bandwidth in 5 GHz)  Packet aggregation: A-MPDU (Tx/Rx) and A-MSDU (Tx/Rx)  802.11 Dynamic Frequency Selection (DFS)  Cyclic Shift Diversity (CSD) support802.11n Version 2.0 (and related) capabilities  2x2 MIMO with two spatial streams  Maximal-Ratio Combining (MRC)  20- and 40-MHz channels  PHY data rates up to 300 Mbps (40-MHz bandwidth in 5 GHz)  Packet aggregation: A-MPDU (Tx/Rx) and A-MSDU (Tx/Rx)  802.11 Dynamic Frequency Selection (DFS) Cyclic Shift Diversity (CSD) supportData rates supported2.4-GHz radio:802.11b: 1  2  5.5  11 Mbps802.11g: 6  9  12  18  24  36  48  54 Mbps802.11n data rates:Interfaces x1 10/100/1000BASE-T auto-sensing PoE+ in (802.3at)Cisco Universal Power over Ethernet (UPOE) in  x2 10/100/1000BASE-T auto-sensing PoE out (802.3af) PoE+ out (802.3at)  x1 fiber SFP (fiber or electrical)  Management console port (RJ-45)  USB 3.0 port  Multicolor system LED  port LED  DC power input  Reset buttonUplink optionsEthernet  SFP  and wireless meshAntennas :Dual bandPoE output : 35.3 W totalMaximum 30W per PSE portUSB interface USB 2.0 / USB 3.0 supportedDimensions (H x W x L)8.5 in. x 7.55 in. x 1.9 in.Weight3.1 lbs.Warranty1 year

Designed for Class I Division 2 hazardous locationsIntelligence with intent-based networking to the IoT Edge and IOx supportPartner IoT modules for WirelessHART  ISA100Cisco DNA Assurance for network management802.11ac Wave 1 and 2 capabilities 2x2 MIMO with two spatial streams Multi- and single-user MIMO Maximal-Ratio Combining (MRC)  802.11ac beamforming (transmit beamforming)  20- 40- and 80-MHz channels  PHY data rates up to 867 Mbps (80-MHz bandwidth in 5 GHz)  Packet aggregation: A-MPDU (Tx/Rx) and A-MSDU (Tx/Rx)  802.11 Dynamic Frequency Selection (DFS)  Cyclic Shift Diversity (CSD) support 802.11n Version 2.0 (and related) capabilities  2x2 MIMO with two spatial streams  Maximal-Ratio Combining (MRC)  20- and 40-MHz channels  PHY data rates up to 300 Mbps (40-MHz bandwidth in 5 GHz)  Packet aggregation: A-MPDU (Tx/Rx) and A-MSDU (Tx/Rx)  802.11 Dynamic Frequency Selection (DFS)  Cyclic Shift Diversity (CSD) support Data rates supported2.4-GHz radio:802.11b: 1  2  5.5  11 Mbps802.11g: 6  9  12  18  24  36  48  54 Mbps802.11n data rates:Interfaces x1 10/100/1000BASE-T autosensing PoE+ In (802.3at)UPOE in  x2 10/100/1000BASE-T autosensing PoE Out (802.3af) PoE+ out (802.3at)  x1 fiber SFP (fiber or electrical)  Management console port (RJ-45)  USB3.0 port  Multicolor system LED  port LED  DC power input (IW-6300H-DC-X-K9  IW-6300H-DCW-X-K9)  AC power input (IW-6300H-AC-X-K9)  Reset buttonUplink optionsEthernet  SFP  and wireless meshDimensions (W x L x H)IW-6300H-DC-X-K9: 9.7" x 11" x 3.8"IW-6300H-DCW-X-K9: 9.7" x 11" x 5.6"IW-6300H-AC-X-K9: 9.7" x 11" x 5.6"Weight13.3 lbs (IW-6300H-AC-X-K9), 9.8 lbs (IW-6300H-DC-X-K9),12.7 lbs (IW-6300H-DCW-X-K9)Warranty1 yearIW 6300 Series  IW-6300H-DC-X-K9: Dual-band 802.11a/g/n/ac  Wave 2  external antennas  44-57VDC/POE+/UPOE power input  IW-6300H-DCW-X-K9: Dual-band 802.11a/g/n/ac  Wave 2  external antennas  10.8-36VDC/POE+/UPOE power input  IW-6300H-AC-X-K9: Dual-band 802.11a/g/n/ac  Wave 2  external antennas  110-220VAC/POE+/UPOE power input